• Influence of SiC addition on tribological properties of SiAlON 

  Mallik, Awadesh Kumar; Reddy, Kolan Madhav; Çalış Açıkbaş, Nurcan; Kara, Ferhat; Mandal, Hasan; Basu, Debabrata; Basu, Bikramjit (Elsevier, 2011)

  The tribological properties of gas pressure sintered SiAlON and its composite with 18 wt% silicon carbide (SiC) against two different mating materials, i.e., alumina and SiAlON are evaluated. SiAlON and SiAlON–18%SiC ...

• The influence of zeolite and powdered Bayburt stones on the water transport kinetics and mechanical properties of hydrated lime mortars 

  Toklu, Yusuf Cengiz; İnce, Ceren; Derogar, Shahram; Yardımcı, Nesrin (Elsevier, 2015)

  The purpose of this paper is an investigation of the possible role of zeolite and powdered Bayburt stones on the fresh and hardened properties of hydrated lime (CL90) mortars. Parameters studied in this paper form the ...

• A comparative study on corrosion of Mg-Al-Si alloys 

  Candan, Şennur; Candan, Ercan (Elsevier, 2017)

  Corrosion behavior of various Mg−Al−Si alloys (AS11, AS21, AS41, AS61 and AS91 series), cast under the same cooling conditions and controlled alloying composition, was investigated systematically. Optical microscopy and ...

• Comparative study on corrosion behaviors of Mg-Al-Zn alloys 

  Candan, Şennur; Candan, Ercan (Elsevier, 2018)

  A comparative study on corrosion behaviors of various Mg−Al−Zn alloys (AZ21, AZ41, AZ61 and AZ91 series, cast under same cooling conditions and controlled alloying composition) was carried out. Scanning electron microscopy ...

• Effect of Activated Carbon Parameters on the Surface Properties of Wheat Straw Residue 

  Şimşek, Yunus Emre (IBCESS, 2016)

  Activated carbon has perfectly developed porosity, a large surface area (up to 3500 m2 g-1), and modifiable surface chemistry properties and exhibits a comparatively high degree of surface reactivity. Due to these reasons, ...

• Properties of Concrete Pavements Produced With Different Type of Fibers 

  Karakurt, Cenk; Arslan, Ahmet Turan (Turkish Chemical Society, 2017)

  Researches demonstrate that fibers boost performance of concrete incredibly. It’s determined that in literature steel fibers increase flexural strength and energy absorption capacity of the cementitious composites. However ...

• INFLUENCE OF NATURAL LIGHTWEIGHT AGGREGATES ON THE PROPERTIES OF CONCRETE 

  Karakurt, Cenk; Özen, Uğur (Turkish Chemical Society, 2017)

  As a result of the developing technology, the construction industry has also gone to a great interest to discover new materials. A lot of literature research has been done for the lightweight aggregates used in the ...

• TUĞLA DUVARLARDA UYGULANAN SIVALARIN ENERJİ VERİMLİLİĞİNİN DEĞERLENDİRİLMESİ 

  Kaya, Turğut; Karakurt, Cenk (Eskişehir Osmangazi Üniversitesi, 2018)

  Energy efficiency is to make the same amount of work by using less energy without compromising the quality and quantity of products and our life. Efficient use of energy is much cheaper than producing energy as a ...

• SAR Görüntülerindeki Arazi Alanlarının Bölge-Tabanlı Segmentasyonu 

  Yayla, Rıdvan; Baha, Şen (IEEE, 2020)

  Sentetik Açıklıklı Radar (SAR) görüntüleri günümüzde çok çeşitli alanlarda yaygın olarak kullanılmaktadır. SAR görüntülerindeki görüntü benekleri ve piksel benzerliklerinden dolayı görüntü segmentasyonu oldukça zordur. Son ...

• CFD simulations of self-compacting concrete with discrete phase modeling 

  Karakurt, Cenk; Çelik, Ahmet Ozan; Yılmazer, Cem; Kiriççi, Volkan; Özyaşar, Ethem (Elsevier, 2018)

  Self-compacting concrete (SCC), is a special type of concrete with high compaction ability in the form-work with its own weight and compacted without any vibration. The main important advantage of SCC is the stability of ...

• LIGHTWEIGHT NATURAL PUMICE COMPOSITES FOR REHABILITATION OF HISTORICAL BUILDINGS AND LANDSCAPE WORKS 

  Özodabaş, Aylin; Karakurt, Cenk (Eskişehir Teknik Üniversitesi, 2020)

  Historical buildings are made of traditional materials such as mud bricks, lime mortars, stone, and wood. Mudbrick is not a durable material against water and compression effects. The aim of this study is to increase the ...

• Influence of marble wastes on soil improvement and concrete production 

  Ural, Nazile; Karakurt, Cenk; Cömert, Ahmet Tuna (Springer, 2014)

  Waste marble dusts are obtained by different methods of cutting marble in marble manufacturing companies. However, environmental damage can occur from the uncontrolled spill of these waste materials in natural habitats. ...

• A New Classification Approach with Deep Mask R-CNN for Synthetic Aperture Radar Image Segmentation 

  Yayla, Rıdvan; Şen, Baha (Kaunas University of Technology, 2020)

  In this paper, a hybrid classification approach which is combined with a more deep mask regionconvolutional neural network and sparsity driven despeckling algorithm is proposed for synthetic aperture radar (SAR) image ...

• Buckling Analysis of a Rotationally Restrained Single Walled Carbon Nanotube 

  Yaylı, Mustafa Özgür (Polish Academic Science Institute Physics, 2015)

  This paper presents an analytical formulation of nonlocal elasticity theory for the buckling analysis of simply supported carbon nanotubes with rotational springs at both ends. The lateral displacement function is represented ...

• Two Pseudo‑Common Vectors for Pattern Recognition 

  Koç, Mehmet; Gülmezoğlu, Mehmet Bilginer; Ergin, Semih; Edizkan, Rıfat; Barkana, Atalay (Springer Heidelberg, 2020)

  In this paper, the mathematical model used in fnding the common vectors of classes in pattern recognition problems is reconsidered to obtain possible alternative solutions for the common vectors. Since the number of ...

• Use of gradient and normal vectors for face recognition 

  Koç, Mehmet; Ergin, Semih; Bilginer Gülmezoğlu, Mehmet; Edizkan, Rıfat; Barkana, Atalay (Wiley, 2020)

  The main objective of this study is to compare face recognition accuracies in the case when the grey levels in eachpixel of the face images are replaced by the gradient and the surface normal vectors. Extensive information ...

• VSI: Environment & Energy 

  Çalışkan, Hakan; Koduru, Janardhan Reddy; Açıkkalp, Emin; Altuntaş, Önder (Elsevier, 2020)

  "VSI: Environment & Energy" isimli yayının özeti bulunmamaktadır.

• Silicon nitride ceramic for all-ceramic dental restorations 

  Özdoğan, Mahmut Sertaç; Güngörmüş, Mustafa; Çelik, Ali; Topateş, Gülsüm (Japanese Society Dental Materials Devices, 2020)

  Silicon nitride (Si3N4) is one of the promising ceramics for dental restoration due to providing significant benefits during the application. This study aimed to investigate the potential use of Si3N4 for all-ceramic ...

• Thermodynamic analysis and multi‑objective optimization performance of solid oxide fuel cell–Ericsson heat engine–reverse osmosis desalination 

  Shakouri, Omolbanin; Assad, Mamdouh El Haj; Açıkkalp, Emin (Springer, 2021)

  This paper targets to consider a hybrid cycle consisting of a solid oxide fuel cell and an Ericsson thermal engine that provides drinking water by connecting to a reverse osmosis desalination unit. First, a parametric ...

• The effect of sintering regime on superhydrophobicity of silicon nitride modified ceramic surfaces 

  Açıkbaş, Gökhan; Çalış Açıkbaş, Nurcan (Taylor & Francis, 2021)

  The most common method of obtaining a superhydrophobic surface is to create a specific surface morphology and then coat it with a hydrophobic polymer. Numerous such morphological surfaces have been developed but are often ...

View more